Rocker cover screw kit containing 16 replacement stainless steel socket cap bolts for round and square barrel engine rocker covers. Only one kit required per engine

To ensure you can easily release these fasteners in years to come we recommend wiping each fastener with copper grease (OIA11070). This kit is for models without billet rocker cover protectors fitted, for models with rocker cover protectors see SSA80015. This kit will suit a V11 with standard rocker cover protectors which are much thinner than aftermarket types.

See SSA81522 for rocker cover trim retaining screws on 2v/cyl CARC models, these are not included with this kit.

 More than 5 in stock

Sump bolt kit containing all replacement stainless steel socket cap bolts for models with a sump extension fitted. Some models e.g. Cali 1100 and series 1 Cali EV models have a sump extension fitted as standard

To ensure you can easily release these fasteners in years to come we recommend wiping each fastener with copper grease (OIA11070). For Cali EV models check whether you have a sump extension fitted, the later one piece deep sump uses SSA80008

 More than 5 in stock

Rocker cover screw kit containing 12 replacement stainless steel socket cap bolts for two valve small twin rocker covers. Only one kit required per engine. Only for twin throttle body V7 models

To ensure you can easily release these fasteners in years to come we recommend wiping each fastener with copper grease (OIA11070). This kit is for models without billet rocker cover protectors fitted. This kit contains the correct screws for the Breva 750 and 2004 on V7 models but does not include the two flanged M5 screws SSA81523 that fasten the rocker cover covers to the rocker cover (on models other than the V7 Racer)

 More than 5 in stock

Kit containing 8 long titanium shouldered retaining screws for your rocker covers. Upgrades the poor quality OE screws with shiny Ti parts

Rocker cover bolt kit for single throttle body models. Upgrade your corrosion prone zinc OE parts with a polished upgrade.

 More than 5 in stock

 887483 MG887483

Screw kit containing 28 replacement stainless steel socket cap bolts for timing cover, inlet manifolds and sump pan. Only one kit required per engine. See SSA87983 and SSA89291 for special rocker cover screw kits

To ensure you can easily release these fasteners in years to come we recommend wiping each fastener with copper grease (OIA11070).

Add a bit of sparkle to your V7!

 More than 5 in stock

Kit containing 8 titanium shouldered retaining screw for rocker cover. Upgrade your corrosion prone zinc OE parts with a polished upgrade.

Rocker cover bolt. We recommend that you check length of bolts on your engine before ordering as two lengths of bolt were used. Supercedes Guzzi ref. 976591
See ENA83249 for rubber sealing washer

 More than 5 in stock

 842291 MG842291

Kit containing 6 titanium shouldered retaining screw for rocker cover. Upgrade your corrosion prone zinc OE parts with a polished upgrade. Note that one bolt on each cover is hidden under a plastic cover, if you would prefer to only buy four bolts then see SSA84291

Rocker cover bolt. We recommend that you check length of bolts on your engine before ordering as two lengths of bolt were used. Supercedes Guzzi ref. 976591
See ENA83249 for rubber sealing washer

 More than 5 in stock

 842291 MG842291

Exhaust stud kit consisting of 4 x titanium studs, 4 x stainless dome head nuts and 4 x stainless wavy washers

The mild steel exhaust studs fitted to modern Guzzis are notorious for corroding in place. Replace yours now with these corrosion resistant parts to ensure you can remove your exhaust in years to come

 More than 5 in stock

1A003632R

M6 flat stainless steel washer

 More than 5 in stock

M5 screw for attaching points cover

2 required per distributor. Can be used in place of hex bolt Guzzi ref. 98082225

 More than 5 in stock